Bresle Kits

Bresle Salt Contamination Kit | Elcometer 138C

All You Need in a Single Kit!

The Elcometer 138 Bresle Salt Kit with the NEW Elcometer 135C Bresle Test Patches. This kit comes complete with everything you need to comply with ISO 8502-6, ISO 8502-9, The Bresle Method. The Elcometer 135C is a self-adhesive rubber film patch with a sealed compartment used for taking samples of soluble salts.

The Elcometer 138 Bresle Kit includes the Elcometer 138 Conductivity Meter. The cartridge type sensor can be easily replaced when necessary and displays conductivity in a range of units including: S/cm, S/m, ppm and % salinity.
 

Bresle Salt Contamination Kit | Elcometer 138B

All You Need in a Single Kit!

This kit comes complete with everything you need to comply with ISO 8502-6, ISO 8502-9, The Bresle Method. The Elcometer 135B is a self-adhesive rubber film patch with a sealed compartment used for taking samples of soluble salts.

The Elcometer 138 Bresle Kit includes the Elcometer 138 conductivity meter. The cartridge type sensor can be easily replaced when necessary and displays conductivity in a range of units including: S/cm, S/m, ppm and % salinity.

Surface Contamination Kit | Elcometer 138/2

The Elcometer 138/2 Surface Contamination Kit provides the means for testing invisible surface contaminants.

Measuring the level of contaminants on a surface prior to application of the coating is essential to ensure the quality of the coating and that its optimum lifetime achieved.

Bresle Test Patches | Box of 25 | Elcometer 135C

The Elcometer 135C Bresle Test Patch determines the concentration of soluble salts on uncoated surfaces in accordance with the ISO 8502-6 test method.

Key features of the Elcometer 135C Bresle Test Patch include:

• Easy to peel off after test, leaving no foam on the substrate
• 19% thicker foam walls than traditional patches - easier to insert a needle
• Sealed compartment with clear flexible membrane for sampling soluble impurities
• Covers on both sides to protect against dust and contaminants
• Supplied with a Certificate of Cleanliness & Test Area
• Available in boxes of 25 & 100

Bresle Test Patches | Box of 100 | Elcometer 135C

The Elcometer 135C Bresle Test Patch determines the concentration of soluble salts on uncoated surfaces in accordance with the ISO 8502-6 test method.

Key features of the Elcometer 135C Bresle Test Patch include:

• Easy to peel off after test, leaving no foam on the substrate
• 19% thicker foam walls than traditional patches - easier to insert a needle
• Sealed compartment with clear flexible membrane for sampling soluble impurities
• Covers on both sides to protect against dust and contaminants
• Supplied with a Certificate of Cleanliness & Test Area
• Available in boxes of 25 & 100

Traditional ISO 8502-6 Bresle Patches | Box of 25 | Elcometer 135B

Elcometer 135B Bresle Patches are the original Bresle Patches manufactured by the Swedish Standards Institute. Used to determine surface chloride contamination and are self-adhesive rubber film patches with a sealed compartment for sampling soluble impurities from steel surfaces with a suitable solvent.

Elcometer Bresle Patches are also available as part of the Elcometer 138 Bresle Salt Kit.
 

Plastic Beaker 30ml (1fl oz)

Standard 1.41 mS/cm Calibration Solution | 6 Bottles

Elcometer 138 conductivity solution for HORIBA Laqua Twin B-771 Conductivity Meter: Consists of six bottles of 1.41 mS/cm. 14ml (0.5fl oz) bottles.

Chloride Test Strips | Pack of 40

Chloride ions on steel surface increase the probability that corrosion of the steel will take place even if a protective coating is applied. Chloride ions trapped under a coating in the presence of steel and moisture will form a corrosion cell. This corrosion process will result in premature failure of the protective coating and may cause blistering of coatings in immersion service.

Chloride test strips will indicate the concentration of chloride ions in the sample solution and if the area of sample collection and volume of water is known the concentration can be measured in parts per million or micro-grams per millimeter.

Ferrous Ion(Iron) Test Strips | Pack of 100 | By Merck

Pack of 100 iron test strips

Method: Colorimetric with test strips

3 - 500 mg/I Fe²⁺